The humimeter GF2 building moisture meter in this configuration makes the tasks and everyday work of restorers and for dehumidification quite easy. Determine the water content in floor screed without a costly CM moisture meter or determine the moisture in insulating materials and brickwork. Estimate the drying cycle or the drying process. Check if your plaster, wood or parquet have already reached the right water content.
- Resolution: 0.1% water content
- Measuring range air humidity 0-100 % r.h.
- Automatic temperature compensation
- Infrared temperature measurement -25 to +125°C / -13 to 257°F
- Measuring area of infrared sensor: 16 cm diameter at a distance of 1 meter
- Non-destructive water content determination of floor screed without CM measuring
- Selectable according to individual requirements
There are other configurations for the humimeter GF2 building moisture meter which can be viewed here.
The humimeter GF2 building moisture meter product package for restoration and dehumidification contains the following sensor systems:
| ||round measuring plate, fix mounted |
article no. 13140
|Building moisture meter with diverse calibration curves for building materials. Choose the correct calibration curve using the arrow keys and press the device onto the material. It is obligatory that the measuring instrument rests on an even and cleaned measuring area.|
| ||attached conductance electronics for GF2 pluggable electronics box with 1 meter cable for connecting external conductivity sensors with BNC connector|
article no. 13141
Necessary adapter for the connection of all sensor types based on the measuring method of conductance with the humimeter GF2.
| ||GF2 ram electrode|
article no. 12630
Checking adequate drying of wood, parquet and so on in order to prevent the formation of shrinkage tears in wooden floors because of a further drying of the wood with the building moisture meter humimeter GF2.
|GF2 pair of plug-in electrodes|
article no. 13011
Measuring plaster to evaluate the approval for subsequent works (tiling, paperhanging, paintwork) in new buildings resp. after water damages with the building moisture meter humimeter GF2.
|GF2 pair of flat electrodes |
article no. 13012
|Condensation and water damages in insulation material, residual moisture measurement in impact sound insulation below the floor screed after water damages.|
Essential depth measurement of ascending moisture, especially for exsiccation processes after water damages deep in the brickworks. Checking the drying of fill in deep layers, especially in case of an unequal fill and consequentially resulting floor unevenness.
|pluggable r.h. sensor 0.5m stainless sensor tube,robust design:|
air humidity 0..100%
article no. 13159
|In addition to both above described applications, with this sensor also the relative humidity and the temperature in the brickwork can be measured. The sensor is equipped with a stainless sensor tube that can problem-free be used also in brickwork, concrete and floor screed. |
|pluggable IR temperature sensor:|
article no. 12513
|Connection of an external infrared temperature sensor. This sensor is equipped with 1:10 optics. This equates a measuring area of 16cm diameter at a distance of 1 meter. With this sensor you can easily detect areas of weak insulation in the wall. Also the functioning of the underfloor heating can be controlled.|
(All sensor probes could be cancelled or additionally ordered if necessary.)
- Measurement within seconds without prior treatment of samples
- Hold function, manual saving of results, datalog for 10.000 logs with measuring point report
- Dimensions 147 x 75 x 30 mm, weight 265g (incl. batteries)
- Large, well-lit LC display
- PC software for data archiving and graphic display of climate data
- No expensive CM measuring necessary
|Art. No.||Picture||Extended Accessories|
|12278||humimeter USB data interface module with LogMemorizer measuring data recording and analysing software on USB flash drive incl. USB cable for PC|
|11929||Plastic case for humimeter GF2|
|12146||Set of 20 replacement tips for measuring electrodes, without isulation 40mm long|
|11775||Set of 20 replacement tips for measuring electrodes, without isulation 60mm long|
|11482||Set of 2 replacement tips for measuring electrodes, isulated, 60mm long|
|13160||Set of measuring bushes for floor screed:|
Plastic bush for driving in a bore hole of a diam eter of 12mm. 20 bushes incl. plug and one hammering aid Suitable for humidity and temperature sensor (Art. No. 13159)
|12881||BNC connecting cable ∅4mm, 100cm Länge (spare part)|
|13224||Extension cable of 8 meters length for humimeter RH2 and GF sensors|
|13051||Wall holder / anti-theft protection for GF2|
Request and consultation
professional building moisture meter
for restoration and dehumidification
Interested in this product? Our specialists will be happy to give comprehensive and free advice on product features and technical solutions. Send your inquiry or just call us on:
+43 3178 28899