Humimeter GF2 Building Moisture Meter
Professional non-destructive moisture meter for concrete, screed, bricks, plasterboard, wood, air humidity, temperature (Infrared) and many other materials and application areas.
The Humimeter GF2 building moisture meter is a professional and versatile building moisture meter which can be extended with various sensors to match your individual needs. As the GF2 offers such a wide variety of functions we recommend some well proven configurations for popular tasks in the building industry. Especially notable is the blazingly fast nondestructive measurement of floor screed without using the tedious CM method.
The GF2 building moisture meter is able to perform lots of measurements relevant for the building industry including: building moisture, air humidity, indoor climate, dew point, equilibrium moisture content, air and surface temperature as well as long-term recording of climate data, incl. material moisture sensor. Optionally available external air humidity and infrared temperature sensors, PC software for data archiving and graphic display of climate data.
- Measuring range building moisture: dependent on the material
- Resolution: 0.1% water content
- Measuring range air humidity 0-100 % r.h.
- Infrared temperature measurement -25 to +125°C / -13 to 257°F
- Measuring area of infrared sensor: 16 cm diameter at a distance of 1 meter
- Measurement of CO2 up to 5000ppm
- Temperature can be set to °C or °F as required
- Automatic temperature compensation
- Measurement within seconds without prior treatment of samples
- Hold function, manual saving of results, datalog for 10.000 logs with measuring point report
- Large, well-lit LC display
- Scope of supply: humimeter GF2 building moisture meter with batteries
- Dimensions 147 x 75 x 30 mm, weight 265g (incl. batteries)
- Required accessories: measuring probes, selectable according to individual requirements
Art. No.: 13140 Humimeter GF2 professional building moisture meter
Handling / measuring procedure
After switching on the unit, select the characteristic curve corresponding to the material to be measured on the measuring unit (for example screed).
Make sure that the surface of the screed is smooth (no protruding parts or impurities) so that the sensor surface of the measuring device can rest flat on the screed. Otherwise, the surface can be scraped off with a spatula or clean chisel and then swept with a broom.
Now the measuring device can be placed on the screed and pressed onto the surface with moderate pressure. The water content is immediately shown on the display.
By effecting various measurements in different areas of the screed, the average water content can be determined immediately. It is also possible to detect moist spots.
The measuring values can be stored on the device, further information like batch number can be added. Via the optional USB interface, the measuring values can be transferred to a PC, and via LogMemorizer ® PC software the data can be archived, exported, processed or printed out.
Many people still use a CM measurement when they want to measure the screed moisture. However, this method of determining the moisture content of the screed offers hardly any advantages and mainly has major disadvantages. On the one hand, CM measurement is expensive and impractical to use, which does not simplify the daily routine on construction sites. On the other hand, only a small area can be investigated with CM measurement, which requires a lot of work. Another factor is the inaccuracy of CM measurement, because who can confirm that the conversion from CM measurement to water content is correct?
To avoid all these problems, the humimeter GF2 moisture meter was developed to determine screed moisture without CM measurement. The fast and non-destructive measurement allows a large area to be tested in a short time by placing the moisture meter on the floor and reading the water content from the display. Therefore, you can use the GF2 moisture meter to determine the moisture content of your screed without the need for expensive CM measurements.
|Art. No.||Picture||Extended Accessories|
humimeter USB data interface module with LogMemorizer measuring data recording and analysing software on USB flash drive incl. USB cable for PC
|12514||Air humidity and temperature sensor for humimeter GF2 building moisture meter|
|12032||Humidity and temperature sensor with 2 meters connection cable|
LF_TB 120 Precision humidity and temperature plug-in sensor for material moisture
Sensor head 0.3 m stainles tube with steel sinter cap and 2 meters connecting calble
|13224||Extension cable of 3 meters length for humimeter RH2 and GF sensors|
|13066||Integrated sensor for parquet floor GF Measurement of relative humidity and temperature|
Cable for integrated sensor for parquet floor GF for connection of the integrated sensor for parquet floor GF (art. no. 13066) to a humimeter device, cable length 2 meters
Humidity and temperature sensor with ∅ 8mm plastic sensor tube. Powered by RH2 resp. GF2, with 2 meters sensor cable, Suitable for measuring bush for floor screed (Art. No. 13160)
Set of measuring bushes for floor screed
Plastic bush for driving in a bore hole of a diameter of 12mm. 20 bushes incl. plug and one hammering aid. Suitable for humidity and temperature sensor (Art. No. 13159)
Non-contact infrared temperature sensor for humimeter GF2
IR- temperature measurement -25 to +125°C / -13 to 257°F. Measuring area: ∅ 16cm at a distance of 1 meter
|13141||External conductance electronics for GF2 |
pluggable electronics box with 1 meter cable for connecting external conductivity sensors with BNC connector incl. connecting cable (Art. No. 12881)
humimeter hand electrode with
10 replacement tips 16mm and
10 replacement tips 23mm. For connection to humimeter GF2 Art. No. 13141 is required!
Pair of plug-in electrodes
For determining of water content of hardened and set building materials. With 10 measuring tips of each 40 and 60mm length. For connection to humimeter GF2 Art. No. 13141 is required!
Pair of flat electrodes, 300mm length
For determination of water content in floor screed resp. insulation, especialy in boarder and floating joints. For connection to humimeter GF2 Art. No. 13141 is required!
|12881||BNC connecting cable ∅4mm, 100cm length (spare part)|
|12630||humimeter WLW Hammer (ram electrode) with BNC cable, without measuring tips. For connection to humimeter GF2 Art. No. 13141 is required!|
|12146||Set of 20 replacement tips for measuring electrodes, without isolation 40mm long|
|11775||Set of 20 replacement tips for measuring electrodes, without isolation 60mm long|
|11482||Set of 2 replacement tips for measuring electrodes, isolated, 60mm long|
|12512||Plastic case for humimeter GF2|
|11929||Plastic case for humimeter BLW, WLW, BL2 and GF2|
|13051||Wall holder / anti-theft protection for GF2|
Request and consultation
humimeter GF2 Building moisture meter
Interested in this product? Our specialists will be happy to give comprehensive and free advice on product features and technical solutions. Send your inquiry or just call us on
+43 3178 28899